Site Search
 

Home Buy Now Products Support Contact Us Services
HHO Development BUY NOW!  Unlimited Email Tech Support for Customers

Unlimited Email Tech Support for Customers - Safety First - Basic Rules for HHO Use
Item 10075 - Classic HHO Cell- $110.00 + S&H

HHO Generator Installation Instructions

 

 

   Ø   Dimensions - 8.5'' tall, 3.5'' in diameter.

Ø Cell Container - Heat treated "Ball" / "Mason" Jar

Ø Capacity - 150+ Milliters per Minute at 80°F at 15 amps and 12.0 volts.  One Teaspoon Sodium Hydroxide.    Mean Elevation - 670 ft above sea level. 

Ø Electrolyte - 1/4 teaspoon Baking Soda mixed with 700 Milliliters of distilled water. 

Ø Filler Cap / Pop-Off Stopper - 1/2'' diameter stopper for easy fill and safety release for high pressure release. 

Ø Electrical Components, (Check Valve and Hose) - Comes with electrical components including wire, relay, fuse holder and fuse, connectors, hose and fittings. Check Valve  ensures safety by eliminating any flashbacks or sparks from your engine accessing the HHO gas in your generator.

 
 
Item 10077 -  Classic HHO Dual Cell -  $189.00 + S&H

Dual Cell for engines up to 4 Liters

Dual Cell HHO Generator Installation Instructions

 

 Includes all components listed above and a second cell to increase HHO production.  Another advantage of the Dual Cell configuration is that the units will remain cooler for a longer period of time.  Each cell pulls only 6.6 volts  which reduces the power which can overheat the cell.

Capacity - At 30 amps and operating at 140 degrees F, the unit will produce in excess of 300 milliliters per minute.

Designed to be used with a MAP/MAF Sensor Enhancer (Item 001) and the Oxygen Sensor Extenders (Item 10087).

Easy to use Filler Caps / Pop-Off Valve - Provides safety and easy to use method of filling cells when needed.

Check valve included to reduce danger from hho ignition.
   
Item 10045 - MAP / MAF  Enhancer - $75.00 + S&H Dual Mode MAP/MAF Sensor Enhancer  $75.00 + Shipping
Select Enhancer Face Color

 
Guaranteed to work as advertised.  This Map / MAF Sensor Enhancer was built directly from the Water4-Gas specifications manual.  It has separate “Hwy” & “City” adjustments along with an “Enhanced” & “Factory” (Original Factory Setting) switch.  This device was designed in accordance with Water4-Gas to work with an HHO generator (Hydrogen Fuel Cell) - Electrolyzer.
; Registration code (if you have it) ; Reglink opened in new frame? ; Name of new frame for reglink ; resolution (1-8) ; Image 1 to load ; Image 2 to load ; Image 3 to load ; Image 4 to load ; Image 5 to load ; link 1 ; link 2 ; link 3 ; link 4 ; link 5 ; statusbar msg on image 1 ; statusbar msg on image 2 ; statusbar msg on image 3 ; statusbar msg on image 4 ; statusbar msg on image 5 ; pause (value = milliseconds). ; Num. of horizontal tiles ; Num. of vertical tiles ; Num. steps for tile rotation (8 .. 32) ; Optional background image ; Red in background (0 .. 255) ; Green in background (0 .. 255) ; Blue in background (0 .. 255) ; Optional image over applet ; Over image X offset ; Over image Y offset ; Memory deallocation delay ; Task priority (1..10) ; Min. milliseconds/frame for sync Sorry, your browser doesn't support Java ; Msg in no java browsers

 

 

 

Dimensions - Length = 3.3'' , Width at bottom = 2.12'', Height = 1.40''. Weight = 3.5 oz. The Enhancer's standard color is Ivory White but also comes in 4 colors: Sky Blue, Lime Green, Sand Tan, and Pastel Rose.  Also included is a detailed installation, usage, tuning & maintenance guide based on information provided from Water4Gas manuals.  Even if you have good mechanical skills, you should have the repair manual for your vehicle to help find the Map sensor and locate the wire that goes from the Map sensor to the computer.  Improper installation of this Map Sensor Enhancer may cause problems with your vehicle’s electrical system. 

If multiple items are purchased, please allow 3 to 4 business days for delivery.

MAP/MAF Sensor Enhancer Installation Instructions
Item 10044 - Glow in the Dark - Dual Mode MAP / MAF Enhancer - $85.00 + shipping & handling Glow in the Dark - Dual Mode MAP/MAF Sensor Enhancer  $85.00 + Shipping

 
This MAP Sensor Enhancer Face actually "Glows" in the dark. It's quite amazing. You can even see the numbers on the dial face, and it really looks cool. 

Includes interlocking cable connector for easy removal.

You also get unlimited email tech support to assist you in installing the Enhancer. 

We will ship your order within 24 hours.

If you are not happy, just return the unit and we will be happy to refund your money.

 

    Feedback 
Item 10087-Oxygen Sensor Extender Kit - $29.95+S&H Oxygen Sensor Extender Kit Contains: 4 Oxygen Sensor Extenders

Concept of the Oxygen Sensor Extender

The Oxygen Extender does away with the need for electronic 'gizmos' that can cost as much as $120.00 or more and rarely work for more than 6 months until they need to be replaced.

By applying the Oxygen Sensor Extender, you have removed the Oxygen Sensor from the direct flow of exhaust and thereby disallowed it's ability to detect oxygen in the exhaust.  Additionally, for the sensor to operate correctly and not set off an error code, the sensor must be subjected to fluctuation in high temperatures of the exhaust and fluctuation in the contents of the exhaust.  This, too, has been completed by the use of the Oxygen Sensor Extender.

 

 The new HHO Development Oxygen Extender now provides a solution to false oxygen signals that trigger the CESL (Check Engine Soon Light) and CEL (Check Engine Light).

Mechanics and HHO developers have continuously tried to find a way to keep the Oxygen Sensors working without sending false signals after installation of an HHO System which introduced large amounts of HHO into the combustion cycle.  This increased the oxygen content of the exhaust gasses which caused the ECM (Electronic Control Module) to increase the air to fuel ratio thus decreasing mpg.  Too clean of a burn was occuring thereby causing the ECM  to think the engine was running too lean and then running the engine in it's default or 'limp home mode', dumping loads of gasoline into the engine and ruining any attempt to increase fuel economy by the use of Hydrogen.

The HHO Development Oxygen Sensor Extender solves all of these problems by simply removing the sensor from the direct flow of exhaust gases, yet still allowing it to fluctuate the signal and heat up from normal operation.  We have discovered the proper angle and size of bore to create a venturi effect around the O2 sensor.  The same gases reach the sensor but they move around the sensor at a higher speed causing a reduced oxygen reading.  No more need for high dollar "EFIE" type circuits or other hard balancing acts in electronics.  You simply place each Oxygen Sensor inside it's own Oxygen Sensor Extender and reinstall them into the exhaust pipe. That's it.

The HHO Development Oxygen Sensor Extender Kit comes with enough parts for one Two Oxygen Sensors and at a cost of only $29.95 plus shipping.  A far cry from the cost of +$240 for an "EFIE" on each sensor!
Warranty

As with all our products, the Extender is guaranteed for as long as you own your vehicle.  If it fails to operate, simply return your product and we will replace it without charge.  Vehicle owner pays shipping if returned after 30 days.

If you are not 100% satisfied with the Extender for any reason, return it to us within 7 days and we will give you a 100% refund, no questions asked.
Item 10090 - High Flow Check Valves 4 for $10.00 + $3.50 shipping & handling Safety First - Buy the Check Valves!

Ø Low Flow Resistance

Ø Low Opening Pressure

 Ø 100% Tested for Back Flow

Ø Positive seal against back flow

Ø Constructed from Acrylic and Silicone

 

Dimensions: 1/4'' x 1-1/4''

Check Valves are a necessary safety feature for every HHO Generator.  Do not connect an HHO Generator to your engine without one (Two are recommended).  HHO explosions are dangerous and "Concussive" which means every precaution should be taken to prevent one.  Check Valves preclude dangerous explosions due to inadvertent sparks in the HHO Generator hose to the air intake.

BE SAFE!
 
 
Item 00043 - Six Cell HHO Distributer $25.00+S&H  HHO Development Six Pack Distributer

Dimensions: Length - 6'', Width - 5''. 1/4'' Diameter Connection for individual cells.  1/2'' Diameter connection to air intake.

 

Item 10088 -  5 Adjustable Bubblers- $15.00  Free Shipping  5 Adjustable Bubblers- $15.00  Free Shipping 

These adjustable bubblers allow air pressure control within the HHO Jar. Used in the original Water4gas HHO design.
Item 10089 -  25 "O" Rings - $10.00  + S&H  25 "O" Rings - $10.00  + S&H 

These "O" Rings are perfect for sealing you HHO Jar when using the plastic lid.
Item 00020 -  30 Amp Bosh Relay- $6.00  
RELAY 30 AMP BOSH $6-00 ea (Free Shipping)

The purpose of the relay is to control the current to the HHO Generator.  When you turn on the ignition, the relay activates the HHO circuit.  This item is necessary to maintain a safe HHO System

 

All Installation Instructions here... Downloads

Dual Mode MAP / MAF sensor Enhancer Quality Parts & Components

·         Toggles Between Enhanced Mode & Your Car’s Original Factory Setting

·         Dual Dials Allow Operator To Set Optimal Performance for city and highway

·         Complete website technical support for our customers - www.hhodevelopment.com

·         Once Set - Operator Only Needs To Toggle Between City Driving & Hwy Driving  (approx. 40 mph or more)  No Knob Adjustment Needed After Set

·         “3 Interlocking Cable Connector” For Ease In Placement Or Removal when in stock

·         Each Unit Is Bench Tested To Assure Reliability

·         Installation Instructions Included

·         Enhancers in Stock Now - Ships Within 48 HRS - Reactor Cells - Allow one week for delivery.

·         USPS Priority Mail For Domestic

·         International Orders Ship First Class Mail

·         Guaranteed to Work as Advertised!

·         Built in USA

  Intervention
Intervention